Epoxy floor recoating revives worn or aging resin surfaces by mechanically abrading the existing coating and applying a system-matched new topcoat or full layer. Surface must be cleaned, tested for adhesion and compatibility, then abraded to meet the required CSP for proper bond. Finished result is a renewed, protective floor with restored appearance and function.
Recoating begins with a detailed evaluation of the current epoxy floor. George Tsinias, owner of USA Epoxy Floors, checks for adhesion, moisture transmission, and any existing chemical or physical damage. The surface is tested for compatibility and bond, while any issues such as contamination, oil, or prior repair materials are identified. The next step is thorough mechanical surface prep, typically by diamond grinding or screening to achieve the correct surface profile specified for the recoat system. Any cracks, divots, or joint damage are repaired with dedicated compounds before recoating. Failed or incompatible coating areas are fully removed as needed, and dust is extracted to ensure the substrate is clean and well-prepared. A system-compatible epoxy, polyaspartic, or urethane recoat is then expertly applied, matching the original or upgraded to meet new performance needs. The floor is finished with a protective topcoat and inspected to ensure even coverage, proper adhesion, and desired appearance. Customers receive a floor with renewed durability and visual appeal, restored for active use.
USA Epoxy Floors does not just cover over existing coatings. George Tsinias evaluates the original resin system, checks for failures caused by moisture, UV damage, or chemical exposure, and confirms if the substrate and previous coats can accept a new layer. This step prevents delamination and ensures every recoat bonds long-term, preventing wasted material and future failures.
Recoating depends on proper surface profile. USA Epoxy Floors uses diamond grinding or abrasive screening to produce a CSP measured surface, tailored to the new coating's requirements, often CSP-2 or CSP-3. This mechanical preparation allows the recoat to bond chemically and mechanically, rather than relying on a light sand or acid etch, which leads to premature peeling.
Recoating is not one-size-fits-all. USA Epoxy Floors identifies whether to use epoxy, polyaspartic, urethane, or another resin, based on original system and intended use. George matches chemical compatibility and finish requirements, matte, gloss, flake, or clear, to extend floor life and return a like-new appearance, even on heavily trafficked surfaces.
Fill in your information below
USA Epoxy Floors provides epoxy floor recoating services for residential, commercial, and industrial properties. George Tsinias, the owner, directly assesses every project and personally manages surface testing, preparation, and recoating to deliver a renewed and fully functional floor. With more than 25 years in the flooring trade, USA Epoxy Floors brings the diagnostic expertise needed to determine if an existing coated floor can be successfully recoated, or if more extensive repairs are necessary. The result is a bonded, visually refreshed epoxy floor that looks and performs like new. Locally owned, family-operated, and veteran-owned since 2001.
More About Us
Yes. USA Epoxy Floors handles Epoxy Floor Recoating throughout Dutchess and the surrounding Dutchess County area. The scope is set after the floor is walked and the slab condition is assessed, so the quote reflects the actual job rather than a generic package.
Work starts with inspecting the slab and testing for moisture where conditions call for it. The surface is mechanically prepared by diamond grinding or shot blasting, damage is repaired, and the coating system is applied in sequence with cure time between coats. The floor is walked through with you at completion.
Most residential-scale work is a one to two day install with cure time before the floor takes traffic. Larger floors and slabs needing significant repair run longer. Polyaspartic topcoats shorten the return to service. Timing specific to your floor is covered at the estimate.
Most structurally sound concrete is. Cracks, pitting, spalling, and existing coatings are handled during preparation. Slabs with active moisture movement are tested first and specified accordingly. If a floor is not a good candidate, you will be told that during the walkthrough.
Mechanical profiling, diamond grinding or shot blasting, so the coating keys into the concrete rather than resting on it. This is the step that determines whether a floor holds. Acid etching alone does not produce a reliable profile and is not used in place of it.
Call or text (845) 464-2539, or use the estimate form. Owner George Tsinias handles the walkthrough and estimate personally in Dutchess, and is on site during the work.
“4 other contractors showed up, did their pitch, and then had to "go back to the office to prepare a quote" - 2 of them never responded and the other two estimates seemed high - George on the other hand showed up, gave me my options and provided a written quote right on the spot that was about 15% less than the other quotes and went on to do a superb job on my garage floor. I would recommend him highly!”
“We are so happy to have discovered George Tsinias. He is an old school artisan and gentleman who takes pride in his work, takes every issue seriously, answers every question, and is a meticulous workman. The garage floor he did for us is stunning. He is humble, fun, courteous, friendly, extremely knowledgeable about adjacent trades and competent in several of them. I am delighted to give him the highest recommendation and look forward to referring him to friends and to using him again.”
“When we called George to give us an estimate on our basement , we knew he was the right guy. He did such a good job in a basement. Then we had him do our two garages. He will never leave a job unless the customer is 100% satisfied. He takes pride in his work. He is a GREAT person to deal with and very responsive and very reasonable.”
“I recently had my basement floor done by USA Epoxy Floors in Fishkill, NY, and I couldn’t be happier with the results. George did an outstanding job from start to finish. He was professional, knowledgeable, and took the time to explain the entire process. The quality of the workmanship is exceptional, the floor came out absolutely beautiful and exceeded my expectations. The attention to detail was impressive, and it’s obvious that George takes great pride in his work. On top of that, the price was very reasonable, especially considering the quality of the finished product. If you’re looking for a company that delivers excellent craftsmanship, great customer service, and fair pricing, I highly recommend USA Epoxy Floors. Thanks again, George, for transforming my basement. It looks fantastic!”
“USA epoxy in Fishkill, New York is one of the greatest epoxy companies I've ever had to deal with George the owner and his crew were amazing. Doing my two floor car garage. The job was finished as promised on time very clean and very professional at their work. I'm in the process of giving them the job of my other house that I have in Long Island New York. And their prices are very, very reasonable compared to other companies. I will definitely recommend.”
“George did an awesome job on our garage floor. He is fair, honest, and timely. He also leaves the site clean when complete.”
“Did an amazing job with our garage. Super professional and easy to work with. Highly recommend.”
Fill in your information below
USA Epoxy Floors is committed to satisfaction & excellence for every customer.
Floor refinishing by USA Epoxy Floors restores worn, damaged, or outdated concrete and resinous surfaces. The process starts with mechanical removal of existing coatings and contaminants, including diamond grinding for a new surface profile. The result is a leveled, repaired base ready for a fresh installation or reseal, delivering renewed performance and appearance.
View Service
Solid color epoxy floor installation delivers a seamless, monolithic resin floor system colored with uniform pigments. Installation includes assessment, moisture testing, diamond grinding, priming, and multiple coats of pigmented epoxy. The outcome is a durable, consistent, chemical-resistant surface for commercial, industrial, or residential use.
View Service
Garage epoxy flooring is the installation of multi-layer resinous floor systems specifically engineered for residential and commercial garage environments. The process includes evaluating the concrete substrate, performing moisture testing, diamond grinding to the correct surface profile, and applying a professional-grade epoxy and topcoat system. The finished garage floor gains chemical protection, resistance to abrasion from hot tires, and a seamless surface that stands up to everyday use.
View ServiceSelect an area of interest to learn more
We provide listings of areas we serve. If you don't see your city, contact us to confirm.
