USA Epoxy Floors provides concrete grinding for slab preparation, leveling, or surface restoration in residential, commercial, and industrial spaces. The process uses diamond grinders to open the surface to the correct profile required for new coatings or sealers. The result is a clean, profiled concrete slab ready for the next step in any flooring system.
Grinding begins with a thorough assessment of the slab's hardness, existing coatings, and any irregularities. George Tsinias, owner of USA Epoxy Floors, determines the appropriate diamond tooling for the material and system going over it. Moisture readings and surface contamination checks are done before equipment is brought on-site. Industrial-grade planetary grinders with selected diamond segments are run across the floor to achieve the specified CSP (Concrete Surface Profile). Edge grinding ensures every corner and wall line is addressed. Dust extraction systems minimize airborne particles and keep the working area clear. The grinding passes are matched to the finish requirement, whether for thin-film coating, high-build epoxy, or a simple grind-and-seal. The process concludes with a careful inspection of the profile and surface cleanliness. If additional cleaning, joint repair, or patching is required, it is performed before any subsequent application. The customer receives a freshly ground floor ready for direct finishing, coating, or as a handoff to another trade with the slab prepared to specification.
USA Epoxy Floors selects diamond tooling and grinding techniques based on the coating system’s CSP profile requirement. Soft bonds are used for hard slabs, and harder bonds for softer concrete. The process is adjusted to meet CSP 2 for lighter decorative systems or up to CSP 5-6 for heavy-duty industrial builds. This ensures the slab accepts the next flooring system as intended.
Improper preparation leaves coatings vulnerable to peeling and delamination. George inspects every slab for contaminants, residue, and surface density, adjusting the grinding pass as necessary. By mechanically profiling the surface instead of using acid etch or chemical cleaners, the new system bonds directly to solid concrete, reducing future failure risk.
Edges and wall lines are ground with hand-held or edge-specific equipment matched to the main grinder’s profile. Full-dust extraction and systematic, overlapping paths result in an even surface from wall to wall with no unaddressed corners or ridges. Concrete grinding is completed as a standalone service or as part of a complete installation with the correct sequence and equipment for every job.
Fill in your information below
USA Epoxy Floors provides concrete grinding for residential, commercial, and industrial floors as both a preparation method and a standalone service. George Tsinias, owner of USA Epoxy Floors, brings over 25 years of flooring experience to every slab assessment and grinding operation. The company’s local ownership, family operation, and veteran roots anchor a process-oriented approach that ensures each floor is ground to the specification needed for the next step, whether it’s a coating, stain, polish, or handoff to general contractors. Every job receives direct oversight from George, who matches the diamond tooling and grinding sequence to the specific demands of the project.
More About Us
Yes. USA Epoxy Floors handles Concrete Grinding throughout Dutchess and the surrounding Dutchess County area. The scope is set after the floor is walked and the slab condition is assessed, so the quote reflects the actual job rather than a generic package.
Work starts with inspecting the slab and testing for moisture where conditions call for it. The surface is mechanically prepared by diamond grinding or shot blasting, damage is repaired, and the coating system is applied in sequence with cure time between coats. The floor is walked through with you at completion.
Most residential-scale work is a one to two day install with cure time before the floor takes traffic. Larger floors and slabs needing significant repair run longer. Polyaspartic topcoats shorten the return to service. Timing specific to your floor is covered at the estimate.
Most structurally sound concrete is. Cracks, pitting, spalling, and existing coatings are handled during preparation. Slabs with active moisture movement are tested first and specified accordingly. If a floor is not a good candidate, you will be told that during the walkthrough.
Mechanical profiling, diamond grinding or shot blasting, so the coating keys into the concrete rather than resting on it. This is the step that determines whether a floor holds. Acid etching alone does not produce a reliable profile and is not used in place of it.
Call or text (845) 464-2539, or use the estimate form. Owner George Tsinias handles the walkthrough and estimate personally in Dutchess, and is on site during the work.
“4 other contractors showed up, did their pitch, and then had to "go back to the office to prepare a quote" - 2 of them never responded and the other two estimates seemed high - George on the other hand showed up, gave me my options and provided a written quote right on the spot that was about 15% less than the other quotes and went on to do a superb job on my garage floor. I would recommend him highly!”
“We are so happy to have discovered George Tsinias. He is an old school artisan and gentleman who takes pride in his work, takes every issue seriously, answers every question, and is a meticulous workman. The garage floor he did for us is stunning. He is humble, fun, courteous, friendly, extremely knowledgeable about adjacent trades and competent in several of them. I am delighted to give him the highest recommendation and look forward to referring him to friends and to using him again.”
“When we called George to give us an estimate on our basement , we knew he was the right guy. He did such a good job in a basement. Then we had him do our two garages. He will never leave a job unless the customer is 100% satisfied. He takes pride in his work. He is a GREAT person to deal with and very responsive and very reasonable.”
“I recently had my basement floor done by USA Epoxy Floors in Fishkill, NY, and I couldn’t be happier with the results. George did an outstanding job from start to finish. He was professional, knowledgeable, and took the time to explain the entire process. The quality of the workmanship is exceptional, the floor came out absolutely beautiful and exceeded my expectations. The attention to detail was impressive, and it’s obvious that George takes great pride in his work. On top of that, the price was very reasonable, especially considering the quality of the finished product. If you’re looking for a company that delivers excellent craftsmanship, great customer service, and fair pricing, I highly recommend USA Epoxy Floors. Thanks again, George, for transforming my basement. It looks fantastic!”
“USA epoxy in Fishkill, New York is one of the greatest epoxy companies I've ever had to deal with George the owner and his crew were amazing. Doing my two floor car garage. The job was finished as promised on time very clean and very professional at their work. I'm in the process of giving them the job of my other house that I have in Long Island New York. And their prices are very, very reasonable compared to other companies. I will definitely recommend.”
“George did an awesome job on our garage floor. He is fair, honest, and timely. He also leaves the site clean when complete.”
“Did an amazing job with our garage. Super professional and easy to work with. Highly recommend.”
Fill in your information below
USA Epoxy Floors is committed to satisfaction & excellence for every customer.
Epoxy floor removal involves mechanically stripping existing epoxy or resinous coatings from concrete substrates. This service uses industrial grinders, shot blasters, and specialized scraping equipment to return the slab to bare, open concrete. Property owners receive a fully prepared surface ready for a new system, flooring installation, or further concrete work.
View Service
Concrete floor leveling from USA Epoxy Floors corrects uneven, sloped, or rough concrete slabs to create a flat, even surface. The process involves mechanical grinding, filling low spots with specialized leveling compounds, and verifying the final plane with precision tools. Customers receive a substrate ready for new flooring, coatings, or use as polished or stained concrete.
View Service
Epoxy floor recoating revives worn or aging resin surfaces by mechanically abrading the existing coating and applying a system-matched new topcoat or full layer. Surface must be cleaned, tested for adhesion and compatibility, then abraded to meet the required CSP for proper bond. Finished result is a renewed, protective floor with restored appearance and function.
View ServiceSelect an area of interest to learn more
We provide listings of areas we serve. If you don't see your city, contact us to confirm.
